8/12/2019 Opcom Fw 1.95 Hex
RE: REPAIR ERASED OP-COM CLONE BOOTLOADER FROM PIC18F458 MCU - genser13 - Hello everyone whether someone can help me for my opcom I managed to do firmware from 1:45 to 1:59 and everything was ok, however I tried to install a new opcom 2015 with hu site and since then the computer recognizes the vastest but certainly will not let me install the drivers tried i'm on several computers.
2017 new Opcom firmware V1.95 China clone diagnostic tool is verified working stable than opcom 1.7 and v1.65.
Software version: VAUX-COM 2014V and 2012V optional
Firmware version: V1.95
Operating system: Windows 7/Windows XP
Activation: No
Opcom fw 1.95 PCB Display:
op-com diagnostic via VAUX-COM 120309a (crack):
2014v VAUX-COM 120309a download:
How to install Opcom V1.95 VAUX-COM Software Driver on Windows 7?
Step 1 Install Driver
Open opcom software CD
Copy Opcom drivers folder to desktop
Extract Opcom 2012+ DB 2014.zip folder
Copy Opcom 2012+ DB 2014 folder to desktop
Connect opcom 1.95 interface with laptop
Device driver software was not successfully installed
No driver found.
Opcon Computer-> Manager->Device Manger-> Other device-> Opcom USB V2 right click Opcom USB V2
select Update Driver Software
Select Browse my computer for driver software
save driver software to C:/Users/AADD/Desktop/Opcom drivers
Windows has successfully updated your driver software
Check now you can see USB Serial Converter right click USB Serial Converter ->Driver tab Driver has been successfully installed
Step 2: Run Self Test (2014V Software)
Open Opcom 2012+ DB 2014 folder on desktop
Run VAUXCOM software as administrator
Select Settings Test interface
Frimware version V01.95
interface test ended successfully
Save configuration.
Step 3: Run 2014V VAUX-COM 120301a
Select Diagnostic functions Select Automatic Vehicle Identification
select KWP-2000
It’s a 1997 Opel Omega-B
opcom v1.95 auto detect vehicle information i.,e VIN, model, engine code etc select diagnose ECM Select Fault codes functions
Check Special Functions of this model
Program immobilizer function options
Output test options
Measuring Blocks options
2014V op-com software also supports GM based SAAB and special PSG5 diesel pump
Step 4: Run optional 2012V opcom
Open Opcom 2012 zip file on software CD
Copy Opcom 2012 folder on desktop
Open Opcom 2012 folder
Run OP-COM setup as administator
Run self test and diagnostic
Done.
Note:
Both Opcom 1.7, V1.65 and V1.95 uses the same VAUX-COM 120309a 2014V software, but opcom 1.95 firmware is more stable than 1.7 and V1.65.
Opcom firmware v1.95 PCB display:
Opcom Firmware V1.7 PCB display(single layer)
Op-com firmware v1.65 PCB display (dual layer)
Who Viewed This Article Also Views:
Introduction
This Instructable will help you set up and use the Opel hardware and software. It is specific to OPCOM V1.45 which was made in China. It was developed a number of years ago and software support has diminished since then. It is for this reason I will show you how to setup this system with a modern laptop, given a minimal amount of downloads and an easy setup. The setup should take no longer than an hour for a novice (not including download time).
The final product of this guide will allow you to check various settings on the computer of your car. You may check fault codes, set steering angles, and vehicle identity. The ability to communicate with your car computer opens a range of possibilities when maintaining or improving your car. Various key aspects of your engines operation and conditions are stored within this system. The ability to communicate with it must be done correctly to avoid causing harm to certain aspects of the car. Always consult the OPCOM Software Guide when in doubt.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |